ECU Tune Studio
Log in Sign up
Bosch EDC15 · EDC16 · VAG TDI

Stage 1 from your original dump.
Inspected before it goes in the car.

Upload the factory file and the system identifies the maps, builds Stage 1, checks every change and corrects the checksum. In a few minutes you get a file ready to flash, with a power and torque estimate.

  • Pay only when you download the result
  • A failed inspection costs nothing
  • Manual map editor included
VW 1.9 TDI PD · 77 kW
EDC16U34 · 03G906021 · Stage 1 strong
✓ Inspection
Power
105 → 131 hp
Torque
250 → 312 Nm
OriginalStage 1rpm →
✓ Changes only inside maps✓ Boost limiter headroom ✓ Independent map detector✓ Checksum corrected

How it works

Four steps, all automatic. You just upload the file and download the result.

1

Upload the original

The full flash read from the car (EDC15 512 KB, EDC16 1–2 MB). Choose a level: mild, standard or strong.

2

Map identification

Two independent detectors and AI find the driver wish, smoke and torque limiters, boost target and boost limiter.

3

Stage 1

Fuel, torque and boost are raised gradually and consistently, within the limits of the chosen level and the engine.

4

Inspection and checksum

Every change is checked, then the checksum is corrected. The result is blocked if anything is wrong.

What the inspection checks

Every file goes through automatic checks plus a second, AI review, as if an experienced tuner looked at it. If something isn't safe, the download is blocked and no credit is used.

Automatic or manual

⚡

Automatic Stage 1

Upload, wait 1–3 minutes and download. You get power and torque charts, a list of every change with original vs Stage 1, and a detailed inspection report.

✎

Manual map editor

For tuners who want to do it themselves. Maps by category, table, 2D and 3D views, hex, version compare, virtual dyno, DTC and checksum. Open the automatic Stage 1 in the editor with one click and refine it.

Step-by-step guide

  1. Read the original from the car. Use a reading tool (KESS, KTAG, Galletto, MPPS…) to read the full flash and store it safely. That file is your only copy of the factory software.
  2. Create an account and log in. Confirm your email and you get 1 free credit.
  3. Upload the file. Drop the .bin or .ori on the start page and pick a level: Mild (~+10 %), Standard (~+15–18 %) or Strong (~+22–25 %, e.g. 1.9 TDI 105 → ~130 hp). If you have a damos (A2L) for that software, add it for exact map names.
  4. Wait for processing. The first time for a given software takes 1–3 minutes; known software is faster.
  5. Review the result. Check the hp and Nm estimate, the charts and the inspection verdict: green is ready, yellow means write with caution (read the notes), red is blocked and costs no credit.
  6. Download Stage 1. Only now is 1 credit used. You can download the same file again later for free.
  7. Flash the car. If the page says the checksum was corrected, the file is ready to write. If not, enable automatic checksum correction in your flashing tool.
  8. Test drive. Check for fault codes (OBD), smoke and clutch slip. If anything shows up, flash the original back.
⚠ Stage 1 increases the load on the clutch, dual-mass flywheel and turbo. Only flash a healthy car and always keep the original.

Pricing

No subscription. Buy credits by card and use them when you need them. Credits never expire.

1 credit = 1 map
€10.00 per credit
  • Automatic Stage 1 with inspection and checksum
  • All three levels for the same file
  • Opening the same file in the manual editor
  • Re-downloads at no extra cost
Sign up: 1 free credit
Never charged
  • Upload and analysis
  • Charts and power estimate
  • Files that fail the inspection
  • Files that are already tuned
Card payments via Stripe.

FAQ

Which ECUs are supported?

Bosch EDC15 (P, V, VM) and EDC16 (U1, U31, U34) from VAG diesels: 1.9 and 2.0 TDI PD, 1.9 TDI VE, V6 TDI. VAG TDI files work best. EDC17 and petrol engines are not supported.

Which file should I upload?

The full flash read from the ECU, factory and unmodified. Don't upload only the calibration area, a WinOLS project (.ols) or an already tuned file.

What if I upload an already tuned file?

The system compares values with factory values and a database of known software. If the file was already modified, Stage 1 is not created, since two tunes would stack, and no credit is used.

Is the checksum corrected?

For most EDC16 and EDC15 files, yes: the checksum is corrected and re-verified, and the page says "Checksum corrected". For rare variants where the algorithm doesn't validate the original, the checksum is left as is, the file is named *_NOCHK.bin and your flashing tool corrects it.

How much power will I gain?

It depends on the engine and level. Typically +10 to +25 % power and torque. The estimate is calculated from the limiter changes and shown on a chart. Real results depend on the condition of the engine, turbo and injection.

Do you do EGR off or DPF off?

No. Disabling emission control systems on road vehicles is not permitted, so this service doesn't offer it.

What about warranty and inspections?

Modified software may affect warranty, type approval and insurance. You flash at your own risk. Read the terms of use.

My question isn't answered here

Reach us via the contact form. We reply by email, usually the same or next business day.

Ready?

Create an account, upload your original and see what your engine can do. The first credit is on us.

Create a free account